#Hp photosmart 7525 printing blank pages driver
Visit the HP Customer Support site for software and driver downloads.If one of your HP printers was affected by the old firmware update, and the resulting blocking of non-HP ink cartridges, you may do the following to restore that functionality again: Firmware updates were however available for all HP printers that I tested. I cannot confirm that they are available for all affected printers as there is no list of all printers affected by the issue initially. Reconnect the power cord to the back of the product.The time has come, as firmware updates are now available for HP printers. Plug the power cord directly into the wall outlet. Relocate the All-in-One to a different power outlet, preferably in a separate room With the product turned on, disconnect the power cord from the back of the product. Make sure that you have the product turned on. Moving the product to another location and plugging it directly into a wall outlet can eliminate any potential power deficiencies that might prevent a successful alignment. Repeat 2 through 5 for each of the cartridges.Ī power reset drains power from the product and returns the product to the same settings after restarting. Slide the new cartridge forward into the empty slot. Remove the new cartridge from its packaging, and then, holding it by the handle, slide the ink cartridge into the empty slot. Do not leave a cartridge outside the HP All-in-One for more than 30 minutes. The product automatically performs an alignment and prints an alignment page.įollow these steps to replace any cartridges that are empty or low on ink.ĬAUTION: Do not replace multiple cartridges at the same time. The gauges for the six cartridges display.Ĭheck the gauge for empty or almost empty cartridges, and then replace any you find. The Tools menu displays.Ĭlick Display Ink Gauge. Follow these steps in the order presented to check the ink levels in the cartridges. Repeat steps 2 through 5 for each of the cartridges.Ĭlose the cartridge door, and then try to align the product again.Įmpty or nearly empty cartridges can result in alignment failures. Secure the cartridge in the slot by pressing down on the latch until it clicks into place. Slide the cartridge back into the empty slot. Do not touch the copper-colored contacts with your hands or anything other than a foam rubber swab or lint-free cloth. Inspect the cartridge contacts for ink and debris buildup.ĭip a clean foam rubber swab or lint-free cloth into distilled water, and then squeeze any excess water from it.
Remove, clean, and then reinstall each cartridge one at a time. Remove the cartridge by pulling it toward you and out of its slot.ĬAUTION: Do not remove multiple cartridges at the same time. Squeeze the tab below the black cartridge on the far left side of the carriage, and then lift the cartridge latch.ġ - Cartridge latch for the black cartridgeĢ - Cartridge latches for the color cartridges Press the Power button to turn on the product. Soft, lint-free materials, such as foam-tipped swabs, that do not stick to the electrical contactsĬlean, lint-free paper to rest the cartridges on (coffee filters work well) Follow these steps in the order presented to clean and reinstall the cartridges. If the contacts on a cartridge are dirty or do not seat correctly, the alignment might fail. Step three: Clean and reinstall the cartridges If the issue persists, see the next step. If these steps resolved the issue, there is no need to continue troubleshooting. If you have trouble viewing the video or to view the video in a different size, click here to play the video (in English) on YouTube.
#Hp photosmart 7525 printing blank pages series
The outside of the product might look different, but the steps are similar for the same for the HP Photosmart 3100, 3200, and 3300 All-in-One series products. The product shown in the video is the HP Photosmart C7280. The following video demonstrates the steps for fixing a carriage or paper jam. The product calibrates, aligns the printhead, and then prints an alignment page. The product opens the Tools menu on the control panel display. NOTE: Look for the brightness level on the paper packaging. Load unused, plain white, letter, or A4-sized paper with a brightness level of at least 85 into the tray. NOTE: Colored, photo, or used paper can cause the alignment to fail.
0 kommentar(er)
